Press & Media

bt_bb_section_bottom_section_coverage_image

TITOLO RIVISTA:

76°Congresso ATI – Volume 312, 2021

TITOLO ARTICOLO:

Some design guidelines to adapt a Darrieus vertical axis turbine for use in hydrokinetic applications (Alcune linee guida di progettazione per adattare una turbina ad asse verticale Darrieus per l’uso in applicazioni idrocinetiche)

AUTORI:

  • Francesco Balduzzi, Pier Francesco Melani, Alessandro Bianchini – Università degli Studi di Firenze
  • Giuseppe Soraperra, Alessandra Brighenti – HE-PowerGreen s.r.l.
  • Lorenzo Battisti – Università di Trento

ESTRATTO:

The use of vertical-axis turbines is raising interest in the field of hydropower production from rivers or water channels, where suitable mass flows are available, without the need of high water jumps or large construction sites. Although many optimization studies on vertical-axis turbines have been carried out for wind applications, lesser examples exist in the technical literature regarding hydrokinetic turbines. In the latter case, the best trade-off between power output and low structural stress is more dependent on the fluid dynamic loadings rather than the inertial loadings, due to the higher fluid density and lower rotation speed. The present work shows the results of an industrial study case application, in which the design of a traditional three-blade Darrieus rotor has been adapted for operating in water flows via hydrokinetic technology. Some specific design rules will be discussed, showing the different concepts adopted for the machine layout in order to achieve the best efficiency and performance. Multiple geometrical parameters of the rotor configuration were involved during the analysis: the number of rotor blades, i.e. two or three blades, the rotor’s shape, i.e. traditional H-shape or unconventional L-shape, and the use of power augmentation systems. The analysis of the numerical results was focused on the following output targets: maximum power coefficient, optimal tip speed ratio (TSR), rotor thrust, blade normal force and the upstream and downstream flow field influence. The outcome of the study shows how the best configuration differs from the common solutions for wind application. Moreover, a high power enhancement can be achieved while guaranteeing a good compromise in terms of structural loads.

Pubblicazione on-line: 22 Ottobre 2021
Link: https://www.sciencedirect.com/science/article/abs/pii/S0960148120304833

TITOLO RIVISTA:

Ocean Engineering – Vol. 234 – Ocean Engineering fornisce un mezzo per la pubblicazione di lavori originali di ricerca e sviluppo nel campo dell’ingegneria oceanica

TITOLO ARTICOLO:

Case study of a cross-flow hydrokinetic turbine in a narrow prismatic canal (Caso di studio di una turbina idrocinetica a flussi incrociati in uno stretto canale prismatico)

AUTORI:

  • L. Battisti, L. Cacciali, S.Dell’Anna – Università degli Studi di Trento
  • G.Soraperra – HE-PowerGreen srl

ESTRATTO:

The performance of a high-solidity H-Darrieus cross-flow hydrokinetic turbine was tested in the subcritical flow of a narrow artificial canal. Turbine shape and swept area were selected to generate high blockage into the flow for mechanical power maximization, although a high axial thrust on the blades was attained. A detailed description of the support structure, probes, and the turbine is provided as a first step of further in-depth studies. After measurements of the undisturbed flow velocity with an acoustic doppler velocimeter, the turbine was submerged to operate at different rotor speeds, while measurements of torque, thrust, and rotor speed were acquired. The water depth at another crossbar was measured continuously to check the backwater profile spreading towards upstream, showing no flooding risk at each rotor speed. Experimental data were analyzed for the torque ripple investigation and high sensitivity to low tip speed ratios was demonstrated.

Pubblicazione on-line: 15 Agosto 2021
Link: https://doi.org/10.1016/j.oceaneng.2021.109281

TITOLO RIVISTA:

Renewable Energy, rivista internazionale di approfondimento scientifico di riferimento per la ricerca e sviluppo di sistemi per lo sfruttamento delle energie rinnovabili , impact factor 5.439.

TITOLO ARTICOLO:

A generalized method to extend airfoil polars over the full range of angles of attack (Metodo generale per l’estensione delle polari di profili fluidodinamici a tutti gli angoli di attacco)

AUTORI:

  • Lorenzo Battisti, Luca Zanne, Marco Raciti Castelli – Università degli Studi di Trento
  • Alessandro Bianchini – Università degli Studi di Firenze
  • Alessandra Brighenti – HE-PowerGreen srl

ESTRATTO:

L’obiettivo generale del lavoro di ricerca presentato nell’articolo è quello di migliorare i modelli numerici per la previsione dei carichi fluidodinamici ai quali sono soggette le turbine ad asse verticale. Tali turbine trovano applicazioni nello sfruttamento energetico di piccola taglia (fino a 30 kW) in ambito eolico, idrocinetico e marino.
Un elemento ritenuto fondamentale dalla comunità scientifica per diffondere la tecnologia è quella di rendere più affidabili i codici utilizzati per stimarne le performance e i carichi sollecitanti. Per migliorare la progettazione, per le turbine ad asse verticale è di fondamentale importanza incrementare l’accuratezza nella previsione del comportamento fluidodinamico del profilo della pala ad elevanti angoli di attacco (cioè in condizione di stallo).
Il lavoro di ricerca pubblicato presenta un nuovo metodo analitico di previsione del comportamento fluidodinamico del profilo della pala basato, validato con dati sperimentali presenti in letteratura e in grado di cogliere gli effetti di una forma arbitraria del profilo aerodinamico (da cui il termine “metodo generale”).

Pubblicazione on-line: 30 marzo 2020
Link: https://www.sciencedirect.com/science/article/abs/pii/S0960148120304833